This shortened version of a Grand Laker canoe is very popular on the big lakes in Maine. It was built by architect Victor Trodella of Yarmouth. It is 16′ 6″ long, 42″ at the beam, and is equipped with a 2 hp Honda outboard, oars and oarlocks, and of course, paddles. Trodella says, “WEST SYSTEM gave me fabulous results… again. Thanks for your advice.” Continue reading →
Scott Oldanie has found many unique uses for WEST SYSTEM Epoxy around his Lemont, Illinois, home. These are just a few. He built two whitetail deer antler replica racks, bonded and carved; a wooden bear head attached to the end of a beam; and repaired damaged moose antlers and rotted log ends of his log home.
We built Huialoha about eight years ago with no blueprints or plans. We started with several pictures of lobster boats from New England and did a Hawaiian version. He had 100 sheets of 3/8” (9.5 mm) marine plywood and about 50 gallons of WEST SYSTEM Epoxy. It took three months to do the hull and the boat in the water. The cabin was added while the boat was in the water. I am still working on the interior teak trim. Every time I go down to the harbor to work on it, I get distracted by Hawaii’s beautiful weather and end up going out for a cruise and swim instead! Continue reading →
Knife makers Cliff Fendley and Mike Carter decided to try their hand at making laminated denim knife handle material. After some research, they chose to use WEST SYSTEM 105 Epoxy Resin with 206 Slow Hardener to laminate pieces of denim fabric into blocks from which they could machine knife handles. Mike first made a 5″ x 7″ piece about 1/2″ thick with alternating front and back layers of blue jean denim. Cliff made a 1″ thick 5″ x 5″ Piece from faded blue jean and 1″ thick 5″ x 5″ piece from faded blue jean and a 1″ thick 1″ x 7″ piece from alternating layers of tan and black denim which he twisted before pressing.
Russell Brown designed and built this single outrigger motorboat for his friend Josh Sutherland. Although not completely finished when the photo was taken, it was “pretty well tested and didn’t seem to have any really bad habits,” says Brown. It is 24′ long and built fairly ruggedly. It uses a 20 hp Yamaha four-stroke and goes about 18 knots with three people on board. Russell, the son of legendary boat designer Jim Brown, designs and builds foils, boats and other composite projects in Port Townsend, Washington. Visit www.ptwatercraft.com.
Growing up in Wesley Hills, New York, Michael Fitzpatrick was influenced by his grandfather, a furniture maker and housewright. He set up his own studio in Boston a few years ago and makes exceptional, handcrafted furniture to order, like the lounge chair (above). He uses WEST SYSTEM Epoxy for most of his projects, especially the bent laminated pieces. He also just purchased a COZY license and is considering using epoxy for the experimental airplane. Visit his website for more information about his handcrafted furniture. www.bostonfurnituremaker.com
Mark Bronkalla of Waukesha, Wisconsin, built this Glen-L Riviera wooden runabout using WEST SYSTEM Epoxy. The Riviera is a 20′ double cockpit traditionally styled wooden runabout. It was built with cold molded construction techniques (epoxy and wood laminations). Top speed as measured by a GPS is 53 mph! For construction photos and building information, visit www.bronkalla.com.
These 31-10 Pacific Class sailboats appeared in Epoxyworks in 18, Fall 2001. They were being rescued and restored by a dedicated group in San Diego, California. John Sutphen, who was involved in the project, sent the photo (below) of one of the restored Pacific Class boats under sail: the reward of hard work and dedication.
This Guillemot kayak (left) is the work of Ed Van Kirk of Constantine, Michigan. Ed built both of these kayaks of redwood and sugar pine, using Nick Shade’s book TheStrip-Built Sea Kayak as a reference. The double seater is a Guillemot kayak, 20′ long with a 30″ beam and weighs 73 lb. The single seater is a Little Auk kayak, 10′ long with a 29″ beam and weighs 43 lb. Ed has also built a 14′ Wee Lassie Two. Continue reading →
This Contender class single-handed racing dinghy was built in Italy by Bonezzi in 1994. Joachim Rosler of New Canaan, Connecticut owns and races the dinghy. He finished the boat with WEST SYSTEM Epoxy and has built his own carbon fiber foils.