Category Archives: Boat Construction

Installing a Teak Deck on ZATARA

by Ken Newell

Cover Photo: The intricate plank layout of ZATARA’s finished teak-covered cockpit, before the hardware was reinstalled.

The Zatara refit project began two years ago when my partner Steve Gallo (a mortgage banker) and myself, Ken Newell (a materials engineer), decided that we wanted something to do with our spare time and money. What we didn’t realize was the level to which the refit project would absorb every weekend and every non-critical dollar we had and cause our significant others to chastise us for our obsessive behavior. Continue reading →

Building Alligator

A Biloxi Lugger

by Bob Walters

Above: The Biloxi lugger Alligator. Bob usually cruises at 9.5 knots and averages about 3.5 mpg. Alligator turns out to be fast, safe, comfortable, and fun.

About ten years ago my wife, Ching, and I decided we wanted a comfortable, easy-to-handle, cruising boat suitable for exploring shallow coastal areas. We’d missed this when we lived aboard our deep draft sailboat 21 years ago. We looked at a lot of boats and decided that we would try a powerboat this time. We liked the features found on Biloxi Luggers, also known as “Chandeleur Boats,” a type indigenous to the upper Gulf Coast. Continue reading →

Old Lady Survives 70 MPH Blast

In the Chicago to Mackinac Race

By Meade Gougeon — GBI Founder

Above: Adagio, Meade Gougeon’s 35′ trimaran in the Chicago to Mackinac Race. This boat is a testament to how many decades wood epoxy structures can last.

The 35′ trimaran Adagio, designed and built by Meade and Jan Gougeon in 1969, survived the harrowing conditions at the finish of the 2002 Chicago to Mackinac race this past year. Continue reading →

Readers’ Projects, Issue 20

Restoration of Pacific Class sailboats

These 31-10 Pacific Class sailboats appeared in Epoxyworks in 18, Fall 2001. They were being rescued and restored by a dedicated group in San Diego, California. John Sutphen, who was involved in the project, sent the photo (below) of one of the restored Pacific Class boats under sail: the reward of hard work and dedication.

Continue reading →

Testing Large Bonded-In Fasteners

by Brian Knight—GBI Technical Advisor

Above: Scheherazade, the 154’7″ yacht that required testing of large bonded-in fasteners.

Cover Photo: The 154’7″ Bruce King-designed Scheherazade resting on her massive keel at Hodgdon Yachts in East Boothbay, Maine.

Scheherazade is a 154′ 7″ Bruce King-designed ketch under construction at Hodgdon Yachts, in East Boothbay, Maine. Scheherazade is 60% larger than Antonisa, the last Bruce King/Hodgdon Yacht collaboration, and is the largest sailboat under construction in the United States. Continue reading →

Readers’ Projects, Issue 19

Ed Van Kirk’s Guillemot Kayak

This Guillemot kayak (left) is the work of Ed Van Kirk of Constantine, Michigan. Ed built both of these kayaks of redwood and sugar pine, using Nick Shade’s book The Strip-Built Sea Kayak as a reference. The double-seater is a Guillemot kayak, 20′ long with a 30″ beam and weighs 73 lb. The single-seater is a Little Auk kayak, 10′ long with a 29″ beam and weighs 43 lb. Ed has also built a 14′ Wee Lassie Two. Continue reading →

Building Optimist Prams

For a Community Sailing Program

By Bruce Niederer — GBI Technical Advisor

Above: Optimist prams built by the SBCSA in the Gougeon boatshop, sailing before the Liberty Bridge on the Saginaw River.

Cover Photo: A new fleet of Optimist prams was built to serve the Saginaw Bay Community Sailing Association

The Saginaw Bay Community Sailing Association (SBCSA) was founded in 1995 by a group of local sailboat racers who shared a vision of a grassroots organization to provide area youngsters and adults a low-cost introduction to sailing. We began that first season with three Transfusion 547’s purchased for the association by Gougeon Brothers, Inc. (GBI) and a half dozen used Optimist prams donated by the Saginaw Bay Yacht Racing Association. Continue reading →

Laminated Canoe Construction Gives Lasting Value

John McKibbin sent pictures of his refinished 18′ laminated canoe. He built it back in 1976 using cold-molded, that is, laminated composite construction, with WEST SYSTEM® epoxy. Laminating a hull is similar to making your own plywood on a three-dimensional mold. While it may take more time and effort to make a laminated hull, the results are well worth it. Continue reading →

Building a Plywood Sharpie – Phase II

Designing & Building the Rudder and Motor Bracket

by Captain James R. Watson

Above: The plywood sharpie is the latest in a long line of boats that Captain James R. Watson has built over his lifetime. Here he is at age 12 with a plywood dinghy he built himself.

Building the rudder

The sharpie’s main reason for existence for over a hundred years is its fine operation in shallow water. However, the conventional sharpie rudder is notorious for causing squirrelly steering, often becoming totally ineffective when the craft heels more than 20°. Most sharpie sailors simply accept the handling aggravations of the conventional rudder in trade for its wonderful steering ability in the shallows. I decided to resolve the traditional faults in steering by installing a special rudder and steering system that has evolved and is used on some contemporary boats. This system will yield maximum control over a wide range of wind and sea conditions while retaining the sharpie’s shallow water virtues. Continue reading →

Paul Butler’s New “Maxi-Mac”

by Paul Butler

Above: The Maxi-Mac is a 14′ river dory designed and built by Paul Butler.

This new river dory, the Maxi-Mac, is an enlarged version of the 90 lb Mini-Mac. It’s double the volume of the smaller boat but lightweight versions of the Maxi-Mac still weigh as little as 125 pounds. LIghter weigh provides capacity for additional payload and easy of handling for getting the boat on and off the water.
Continue reading →