Cover Photo: Paddling the south shore of Ontario’s Lake of Two Rivers and into Pog Lake.
It all began when we went camping in Algonquin Park in 2005. We rented a couple of plastic kayaks and the kids loved it. We came home with the intention of buying a couple of kayaks but while on the internet we saw these stitch and glue make’m yourself boats. I purchased the books “The New Kayak Shop” and “Kayaks You Can Build. ”Both are available at Chapters or Amazon.com. We decided this was something we could do. We also discovered www.clcboats.com which would prove to be a tremendous source of encouragement during the project. We made a day trip to Toronto to purchase plans for a Continue reading →
Bob, my brother-in-law, has a beautiful yard that he has set in a nautical theme. He had been looking at lighthouse plans and asked if I was interested in helping build one with WEST SYSTEM® epoxy. All the plans that he looked at were for flat paneled six or eight-sided lighthouses built with plywood. I was interested in a project that was a bit more challenging and unique, so I suggested we build a stripped plank version. That way the tower could be round and tapered like many of the popular lighthouses around the world and it would differ from the flat-sided variety often seen in people’s yards. Bob liked the idea, so he went online and found photos of lighthouses that he liked. In the end, we based our design on the Marblehead lighthouse located on the southwestern shore of Lake Erie. Continue reading →
Spot prime metals with G/5 in place of slower drying paint primers for indoor applications prior to applying latex paints. Latex paint can be applied to G/5 about ten minutes after the epoxy is applied and while the epoxy is still soft. G/5 provides a thin barrier and prevents rust that otherwise forms in latex paint when it dries over bare steel.
Model railroad set builders create natural looking surfaces by applying a film of G/5 adhesive and then sprinkling small objects onto the surface while it is still uncured. These Continue reading →
Adagio, our 35′ trimaran, was already off to a bad start in the 100th anniversary of the first running of the Chicago to Mackinaw race with an over-early call by the race committee. Everything went downhill from there. Continue reading →
Composites are a blend of resin (in this case mixed epoxy) and reinforcing fiber. Folks often ask, “How strong are they?” It is difficult to answer this question due to many variables including resin type, fiber type, fiber orientation, and resin/fiber ratio. To give a value for a laminate, we reduce the variables. Values shown in this article were done with test samples using WEST SYSTEM 105 Epoxy Resin®/206 Slow Hardener® at room temperature (70°F). Reinforcing fibers are Episize™ materials. Laminates made for the test had fibers oriented in one direction (unidirectional) and were laminated using Continue reading →
Glenn Curtiss is recognized as the “Father of Naval Aviation.”He trained the first Navy pilots and built their first aircraft, the A-1 Triad Amphibian. It was “Curtiss Pushers” in 1910 and 1911, that demonstrated capability to take off and land on a ship, leading to the development of aircraft carriers. Continue reading →
At two-part adhesive in a convenient, self-metering cartridge for permanent, waterproof structural gap filling and gluing.
Six10® Adhesive gives you the strength and reliability of a two-part WEST SYSTEM epoxy with the convenience of a single part product. Six10 is dispensed with a standard caulking gun. Non-sagging Six10 bonds tenaciously to wood, metals, fiberglass and concrete. It cures in temperatures as low as 50°F. Working time is 42 minutes at 72°F. Cures to a solid in 5–6 hours and will take high loads in 24 hours. Cure time is faster at warm temperatures and Continue reading →
WEST SYSTEM® Six10 is a two-part, pre-thickened epoxy adhesive formulated with properties that make it perfect for many adhesive applications. Compared to other ready-to-dispense adhesives, its particular physical properties make it ideal for stitch and glue boat construction, fiberglass laminate repair and general bonding. This new formulation has a good balance between the elongation and toughness of G/flex® and the strength and stiffness of our 105 Resin-based epoxies. You can use it with as many materials as possible including wood, metals and composites. The long working time with fast thru-cure and unique shear thinning are additional characteristics formulated into Six10 that contribute to its ease of use. Continue reading →
The WEST SYSTEM® Six10 cartridge is comprised of the cartridge body, removable nose plug and a threaded retaining nut. A 600 static mixer is included with the cartridge. (It’s called a static mixer because it has no moving parts.) The cartridge fits into any standard caulk gun—manual, cordless or pneumatic—and allows simultaneous dispensing and mixing of the two-part epoxy. Manual caulking guns are graded by mechanical advantage (MA) in relation between the travel of the pistol grip and the plunger. When using he static mixer, resistance Continue reading →
By J.R. Watson For many decades Gougeon Brothers Inc. has kept in contact with multihull designer James Wharram. Wharram, of Cornwall, UK, has sailed and designed Polynesian-style catamarans for 50 years. Amateurs and professionals have built his boats and sailed them to all corners of the planet. The designs he creates with his engineer and artist partner Hanneke Boon have evolved over the years, but remain unmistakably, Wharram Catamarans. Continue reading →